Exterior Finishing: Galvanized Metal

Expanded flange control joint

#15 Expanded Flange Control Joint (Double-V) is used to relieve stresses in large plastered areas of walls, ceilings, and stucco areas. The Double-V Control Joint counteracts the inherent shrinkage during stucco…

GALVANIZED STEEL Expanded flange corner bead for exterior corners

A solid nose, all-purpose exterior corner bead. Strong and economical with multiple general use purposes.

Expanded flange inside corner control joint

#30 Corner Master™ Expansion/Contraction Control Joint (Double-V) is designed to provide stress relief at inside corner intersections on plaster walls. The Double-V expansion joint absorbs…

Exterior Foundation sill screed

A variation of the #7 style screed which allows trowel access underneath the screed to clean excess stucco material. No visible metal is seen below the stucco line.

Two-piece expansion control joint

#40 Expansion Joint is a two-piece, slip joint that finishes butt ends of adjacent panels in wide or tall walls and ceilings to allow for multi-directional movement.

Short flange casing bead to terminate stucco or plaster edge

Used as a stucco/plaster stop to provide a screed edge and protective finish trim while terminating plaster in a clear, straight line at windows, doors, and other openings.

Expanded flange casing bead or plaster stop

Used as a stucco/plaster stop to provide a screed edge and protective finish trim while terminating plaster or thin stone in a clear, straight line at doors, windows, and other openings.

Provides clean, neat edge protection at gypsum panel terminations for one- and two-coat veneer plaster finishes

Veneer trims 701A and 801A are J-shaped trims formed from galvanized steel to fit standard 1/2" and 5/8" gypsum panel depths with…

Applied after panel installation to finish veneer plaster edges at wall terminations

Veneer trims 701B and 801B are L-shaped trims designed for use at junctions of veneer gypsum base with rough concrete or masonry ceilings.

Expanded flange control joint with a taped reveal for a clean finish

#XJ15 Expanded Flange Control Joint (Double-J) is used to relieve stresses in large plastered areas of walls, ceilings, and stucco areas. This expanded wing control joint…

Used as a casing stop bead with stucco, stone and E.I.F.S. Systems

2" Nominal J-Weep Low-Back (2-inch back flange) is commonly used as a straight edge plaster stop at the top of doors and windows over traditional head flashings.

Used as sill weep screed or at door and window opening

J-Weep High-Back Plaster Stop is a J-shaped, square-nosed trim manufactured from 26-gauge galvanized steel. The 1-3/8" ground is designed for use with 1" of foam, lath, and a one-coat…

The most rigid of all expanded metal lath products

A High-Rib Metal Lath with a herringbone mesh pattern and seven, 3/8" deep, longitudinal, solid steel ribs at intervals of 3-7/8" across the sheet. These ribs provide the superior strength…

Reinforcement for inside or outside corners

Cornerite™ reinforcing angle is used to reinforce all inside or inner plaster corners to reduce corner cracking. Cornerite reinforcing angle is formed from finished, edge strip lath and bent…

Galvanized, Expanded Steel Plaster aND Stucco Base

A superior, multi-purpose expanded steel substrate for Portland cement or widely used for interior and exterior gypsum plaster and stucco & stone reinforcement. Applications include…

A Heavy-gauge lath for Enhanced protection from breach

Diamond Security Lath is an expanded steel base used for interior and exterior plaster and stucco reinforcement for secured applications where advanced breech protection is required.

Exterior foundation WEEP (sill) screed 

The FHA-7 is for hard-coat stucco, thin-veneer stone, and 1-coat stucco over foam applications. Installed at the juncture of the sill and the exterior concrete foundation, it allows trapped…

heavy duty Reinforcing

Mega Lath is a self-furring welded wire that provides heavy-duty reinforcing for both stucco and stone installation.

Provides superior keying for joint compound for one-coat plaster veneer systems

Mini-Bead™ 800 and 900 are fine-mesh corner beads used to provide corner reinforcement for one-coat and two-coat veneer plaster systems. 1-1/4" wide fine-…

Galvanized Expanded Steel Plaster/Stucco Base

A superior mesh multi-purpose expanded steel base with an approved Grade-D weather resistant barrier attached. Application of asphalt paper-backed (APB) metal lath is used behind stone,…

1/4" self-furring, dimpled, Expanded Steel Plaster and Stucco Base

A self-furring expanded dimpled metal lath ideal for interior and exterior use over sheathing, masonry, and other solid surfaces as required per ASTM C847, ASTM C1780, ASTM…

1/4" self-furring v-groove Expanded Steel Plaster or Stucco Base

Self-Furring V-Groove Metal Lath is manufactured with five, approximately 1/4" deep, embossed “V” ribs, spaced 6" on center along the length of the sheet. The V’s allow…

more rigid than diamond lath and helps to prevent Plaster loss

3-3/16" wide strips of plain 50lb kraft paper spot attached with glue between the herringbone mesh pattern with seven, 3/8" deep longitudinal solid steel ribs spaced at 3-7/8"…

Reinforcement for corners, windows, doors and openings

Striplath is a flat, expanded metal strip used as plaster reinforcement over joints of solid bases and where dissimilar bases join. It is flexible for use over irregular surfaces.

Stucco Reinforcing

Structa Wire lath is a welded wire lath, engineered to enhance the performance of stucco cladding and is a part of the ClarkDietrich Easy Embedment System.

Superior Stucco Reinforcing

Structalath Twin Trac is an innovative reinforcing lath that simplifies the attachment of lath to wood and steel studs.

Corner Reinforcing

Innovative Structa V Truss is the result of our continued commitment to providing the best lathing products possible.

wall & ceilings Reinforcing

V Truss for Walls & Ceilings is designed to improve the performance of stucco on overhead surfaces.